|
Starts a new design case in a separate worksheet (view). Will
prompt you to decide if the new design case will be operating
in batch or continuous mode. For more see Start
New Design Case File command. |
|
Will open an existing design case file in a separate worksheet
(view). Will bring up the Open File dialog. You can select multiple
file to open the all at once. For more see Open
an Existing Design Case File command. |
|
Will save the active design case to its current file name and
directory. If the design case hasn’t been saved before will
bring up the File Save As dialog. For more see Save
a Design Case command. |
|
Will save all the open design cases into their current file
name and directories. If an open design case has not been saved
before it will bring up the File Save As. For more see Save
All Open Design Cases command. |
|
Will erase from the flowsheet the selected item(s) irreversibly.
It is active only if any items are selected. For more see Clear
command. |
|
Will remove from the flowsheet the selected item(s) and place
a copy into the clipboard, so that they can be pasted elsewhere.
It is active only if any items are selected. For more see Cut
to Clipboard command. |
|
Will place a copy of the selected item(s) to the clipboard
so that they can be later pasted elsewhere. It is active only
if any items are selected. For more see . |
|
Will paste the contents of the clipboard into the flowsheet.
The items are pasted in a location such that their enclosing rectangle
is centered around the last mouse click (prior to the paste command).
For more see Paste command |
|
Will allow the user to restore the file to a previously recorded
state. See also Undoing
and Redoing. |
|
Will allow the user to restore the file to a later recorded
state. See also Undoing
and Redoing. |
|
Places the mouse in Select
Mode. In this mode, mouse clicks are used to select (or if
the CTRL key is down, add to the selection) an item (unit procedure,
stream, etc.) |
|
Places the mouse in Connect
Mode. In this mode, mouse clicks are used to start connection
streams (if they occur over an output port and before a stream’s
drawing has started) or create elbows of connection streams (if
they happen after the stream drawing has started). For more on
how to create streams, see Stream
Drawing (Chapter 4 of manual). |
|
Will start the Mass & Energy (M&E) Balance calculations
(simulation) (F9). See also Solve
M&E Balances Command. |
|
Will perform the economic calculations (Shift + F9). See also
Perform
Economic Calculations Command. |
|
Will show (if the toolbar is not visible) or hide (if the toolbar
is visible) the visual objects toolbar (see Visual Objects toolbar.)
With that toolbar you enhance the appearance of the flowsheet
by adding rectangle boxes, ellipses, comments, etc. See also Visual
Objects Toolbar Command. |
|
Will show or hide the process explorer registry toolbar (see
Process Explorer).
This toolbar displays in tree form all the resources registered
in the current process. See also Process
Explorer Toolbar Command. |
|
Will show or hide the overview (navigation) window (see Overview (Navigation)
Window). You can use this window to see an overview of the
entire flowsheet drawing, and quickly change the area viewed currently
in the active worksheet. See also Overview
Navigator Command. |
|
Will show or hide the stream summary table (see Stream Summary
Table). This table displays a set of user-selected stream
properties for a set of user-selected streams. See also Stream
Summary Table Command. |
|
Will show or hide the error output table (see Error Output).
This table shows any errors or warnings produced during the use
of the ProDesigner application. See also View
Error Output Toolbar Command. |
|
Will show or hide the simulation control toolbar (see Simulation
Control Toolbar). Once the simulation has been paused by a
user-set solution breakpoint (see Breakpoints in a Unit Procedure).
From this toolbar you can control how the simulation should proceed.
See also Simulation
Control Toolbar Command. |
|
Will show or hide the Process Library interfaces (see Process
Library Toolbar). See also Toggle
the Process Library Interface Command. |
|
Will initiate the printing process for the currently active
flowsheet. Will bring up the usual "Print Dialog" that
allows you to select a printer, set printer options, etc. See
also Print Command. |
|
Will put the cursor in the "What-Is" help mode. Click
on this button and then on any item of the interface (menu, button,
toolbar, etc.) to bring up a related help topic. The best way
to interactively discover new features of Pro-Designer! See also
Help Topics Command. |
|
Will bring up version information about your current installation
of Pro-Designer. See About
Command. |
